Difference between revisions of "Peer-To-Peer Protocol"

(Created page with "This page describes the Bitcoin Network Protocol used by nodes running the BitcoinSV node client to communicate transaction and block information on the BitcoinSV network. Thi...")
 
Line 945: Line 945:
  
 
* [[Network]]
 
* [[Network]]
 +
 +
==Attribution==
 +
This content is based on content sourced from https://en.bitcoin.it/wiki/Protocol_documentation under [https://creativecommons.org/licenses/by/3.0/ Creative Commons Attribution 3.0]. Although it may have been extensively revised and updated we acknowledge the original authors.

Revision as of 12:41, 17 February 2020

This page describes the Bitcoin Network Protocol used by nodes running the BitcoinSV node client to communicate transaction and block information on the BitcoinSV network. This is a current standard means for nodes to communicate information about the ledger between each other including valid transactions, block discovery messages and more.

For protocol used in mining, see GetBlockTemplate interface.


Message structure

Field Size Description Data type Comments
4 magic uint32_t Magic value indicating message origin network, and used to seek to next message when stream state is unknown
12 command char[12] ASCII string identifying the packet content, NULL padded (non-NULL padding results in packet rejected)
4 length uint32_t Length of payload in number of bytes
4 checksum uint32_t First 4 bytes of sha256(sha256(payload))
? payload uchar[] The actual data


Known magic values:

Network Magic value Sent over wire as
mainnet 0xE8F3E1E3 E3 E1 F3 E8
testnet 3 0xF4F3E5F4 F4 E5 F3 F4
scaling testnet 0xF9C4CEFB FB CE C4 F9
regtest 0xFABFB5DA DA B5 BF FA

Variable length integer

Integer can be encoded depending on the represented value to save space. Variable length integers always precede an array/vector of a type of data that may vary in length. Longer numbers are encoded in little endian.

Value Storage length Format
< 0xFD 1 uint8_t
<= 0xFFFF 3 0xFD followed by the length as uint16_t
<= 0xFFFF FFFF 5 0xFE followed by the length as uint32_t
- 9 0xFF followed by the length as uint64_t

If you're reading the Satoshi client code (BitcoinQT) it refers to this encoding as a "CompactSize". Modern BitcoinQT also has the CVarInt class which implements an even more compact integer for the purpose of local storage (which is incompatible with "CompactSize" described here). CVarInt is not a part of the protocol.

Variable length string

Variable length string can be stored using a variable length integer followed by the string itself.

Field Size Description Data type Comments
1+ length var_int Length of the string
? string char[] The string itself (can be empty)

Network address

When a network address is needed somewhere, this structure is used. Network addresses are not prefixed with a timestamp in the version message.

Field Size Description Data type Comments
4 time uint32 the Time (version >= 31402). Not present in version message.
8 services uint64_t same service(s) listed in version
16 IPv6/4 char[16] IPv6 address. Network byte order. The original client only supported IPv4 and only read the last 4 bytes to get the IPv4 address. However, the IPv4 address is written into the message as a 16 byte IPv4-mapped IPv6 address

(12 bytes 00 00 00 00 00 00 00 00 00 00 FF FF, followed by the 4 bytes of the IPv4 address).

2 port uint16_t port number, network byte order

Hexdump example of Network address structure 

0000   01 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00  ................
0010   00 00 FF FF 0A 00 00 01  20 8D                    ........ .

Network address:
 01 00 00 00 00 00 00 00                         - 1 (NODE_NETWORK: see services listed under version command)
 00 00 00 00 00 00 00 00 00 00 FF FF 0A 00 00 01 - IPv6: ::ffff:a00:1 or IPv4: 10.0.0.1
 20 8D                                           - Port 8333

Inventory Vectors

Inventory vectors are used for notifying other nodes about objects they have or data which is being requested.

Inventory vectors consist of the following data format:

Field Size Description Data type Comments
4 type uint32_t Identifies the object type linked to this inventory
32 hash char[32] Hash of the object


The object type is currently defined as one of the following possibilities:

Value Name Description
0 ERROR Any data of with this number may be ignored
1 MSG_TX Hash is related to a transaction
2 MSG_BLOCK Hash is related to a data block
3 MSG_FILTERED_BLOCK Hash of a block header; identical to MSG_BLOCK. Only to be used in getdata message. Indicates the reply should be a merkleblock message rather than a block message; this only works if a bloom filter has been set.
4 MSG_CMPCT_BLOCK Hash of a block header; identical to MSG_BLOCK. Only to be used in getdata message. Indicates the reply should be a cmpctblock message. See BIP 152 for more info.

Other Data Type values are considered reserved for future implementations.

Block Headers

Block headers are sent in a headers packet in response to a getheaders message.

Field Size Description Data type Comments
4 version int32_t Block version information (note, this is signed)
32 prev_block char[32] The hash value of the previous block this particular block references
32 merkle_root char[32] The reference to a Merkle tree collection which is a hash of all transactions related to this block
4 timestamp uint32_t A timestamp recording when this block was created (Will overflow in 2106<ref>https://en.wikipedia.org/wiki/Unix_time#Notable_events_in_Unix_time</ref>)
4 bits uint32_t The calculated difficulty target being used for this block
4 nonce uint32_t The nonce used to generate this block… to allow variations of the header and compute different hashes
1+ txn_count var_int Number of transaction entries, this value is always 0

cf. Block hashing algorithm

Differential encoding

Several uses of CompactSize below are "differentially encoded". For these, instead of using raw indexes, the number encoded is the difference between the current index and the previous index, minus one. For example, a first index of 0 implies a real index of 0, a second index of 0 thereafter refers to a real index of 1, etc.

PrefilledTransaction

A PrefilledTransaction structure is used in HeaderAndShortIDs to provide a list of a few transactions explicitly.

Field Name Type Size Encoding Purpose
index CompactSize 1, 3 bytes Compact Size, differentially encoded since the last PrefilledTransaction in a list The index into the block at which this transaction is
tx Transaction variable As encoded in tx messages The transaction which is in the block at index index.

See BIP 152 for more information.

HeaderAndShortIDs

A HeaderAndShortIDs structure is used to relay a block header, the short transactions IDs used for matching already-available transactions, and a select few transactions which we expect a peer may be missing.

Field Name Type Size Encoding Purpose
header Block header 80 bytes First 80 bytes of the block as defined by the encoding used by "block" messages The header of the block being provided
nonce uint64_t 8 bytes Little Endian A nonce for use in short transaction ID calculations
shortids_length CompactSize 1 or 3 bytes As used to encode array lengths elsewhere The number of short transaction IDs in shortids (ie block tx count - prefilledtxn_length)
shortids List of 6-byte integers 6*shortids_length bytes Little Endian The short transaction IDs calculated from the transactions which were not provided explicitly in prefilledtxn
prefilledtxn_length CompactSize 1 or 3 bytes As used to encode array lengths elsewhere The number of prefilled transactions in prefilledtxn (ie block tx count - shortids_length)
prefilledtxn List of PrefilledTransactions variable size*prefilledtxn_length As defined by PrefilledTransaction definition, above Used to provide the coinbase transaction and a select few which we expect a peer may be missing

See BIP 152 for more information.

BlockTransactionsRequest

A BlockTransactionsRequest structure is used to list transaction indexes in a block being requested.

Field Name Type Size Encoding Purpose
blockhash Binary blob 32 bytes The output from a double-SHA256 of the block header, as used elsewhere The blockhash of the block which the transactions being requested are in
indexes_length CompactSize 1 or 3 bytes As used to encode array lengths elsewhere The number of transactions being requested
indexes List of CompactSizes 1 or 3 bytes*indexes_length Differentially encoded The indexes of the transactions being requested in the block

See BIP 152 for more information.

BlockTransactions

A BlockTransactions structure is used to provide some of the transactions in a block, as requested.

Field Name Type Size Encoding Purpose
blockhash Binary blob 32 bytes The output from a double-SHA256 of the block header, as used elsewhere The blockhash of the block which the transactions being provided are in
transactions_length CompactSize 1 or 3 bytes As used to encode array lengths elsewhere The number of transactions provided
transactions List of Transactions variable As encoded in tx messages The transactions provided

See BIP 152 for more information.

Short transaction ID

Short transaction IDs are used to represent a transaction without sending a full 256-bit hash. They are calculated by:

  1. single-SHA256 hashing the block header with the nonce appended (in little-endian)
  2. Running SipHash-2-4 with the input being the transaction ID and the keys (k0/k1) set to the first two little-endian 64-bit integers from the above hash, respectively.
  3. Dropping the 2 most significant bytes from the SipHash output to make it 6 bytes.

See BIP 152 for more information.

Message types

version

When a node creates an outgoing connection, it will immediately advertise its version. The remote node will respond with its version. No further communication is possible until both peers have exchanged their version.

Payload:

Field Size Description Data type Comments
4 version int32_t Identifies protocol version being used by the node
8 services uint64_t bitfield of features to be enabled for this connection
8 timestamp int64_t standard UNIX timestamp in seconds
26 addr_recv net_addr The network address of the node receiving this message
Fields below require version ≥ 106
26 addr_from net_addr The network address of the node emitting this message
8 nonce uint64_t Node random nonce, randomly generated every time a version packet is sent. This nonce is used to detect connections to self.
? user_agent var_str User Agent (0x00 if string is 0 bytes long)
4 start_height int32_t The last block received by the emitting node
Fields below require version ≥ 70001
1 relay bool Whether the remote peer should announce relayed transactions or not, see BIP 0037

A "verack" packet shall be sent if the version packet was accepted.

The following services are currently assigned:

Value Name Description
1 NODE_NETWORK This node can be asked for full blocks instead of just headers.
2 NODE_GETUTXO See BIP 0064
4 NODE_BLOOM See BIP 0111
1024 NODE_NETWORK_LIMITED See BIP 0159

Hexdump example of version message (OBSOLETE EXAMPLE: This example lacks a checksum and user-agent): 

0000   F9 BE B4 D9 76 65 72 73  69 6F 6E 00 00 00 00 00   ....version.....
0010   55 00 00 00 9C 7C 00 00  01 00 00 00 00 00 00 00   U....|..........
0020   E6 15 10 4D 00 00 00 00  01 00 00 00 00 00 00 00   ...M............
0030   00 00 00 00 00 00 00 00  00 00 FF FF 0A 00 00 01   ................
0040   20 8D 01 00 00 00 00 00  00 00 00 00 00 00 00 00   ................
0050   00 00 00 00 FF FF 0A 00  00 02 20 8D DD 9D 20 2C   .......... ... ,
0060   3A B4 57 13 00 55 81 01  00                        :.W..U...

Message header:
 F9 BE B4 D9                                                                   - Main network magic bytes
 76 65 72 73 69 6F 6E 00 00 00 00 00                                           - "version" command
 55 00 00 00                                                                   - Payload is 85 bytes long
                                                                               - No checksum in version message until 20 February 2012. See https://bitcointalk.org/index.php?topic=55852.0
Version message:
 9C 7C 00 00                                                                   - 31900 (version 0.3.19)
 01 00 00 00 00 00 00 00                                                       - 1 (NODE_NETWORK services)
 E6 15 10 4D 00 00 00 00                                                       - Mon Dec 20 21:50:14 EST 2010
 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 FF FF 0A 00 00 01 20 8D - Recipient address info - see Network Address
 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 FF FF 0A 00 00 02 20 8D - Sender address info - see Network Address
 DD 9D 20 2C 3A B4 57 13                                                       - Node random unique ID
 00                                                                            - "" sub-version string (string is 0 bytes long)
 55 81 01 00                                                                   - Last block sending node has is block #98645

And here's a modern (60002) protocol version client advertising itself to a local peer...

Newer protocol includes the checksum now, this is from a mainline (satoshi) client during an outgoing connection to another local client, notice that it does not fill out the address information at all when the source or destination is "unroutable". 


0000   f9 be b4 d9 76 65 72 73 69 6f 6e 00 00 00 00 00  ....version.....
0010   64 00 00 00 35 8d 49 32 62 ea 00 00 01 00 00 00  d...5.I2b.......
0020   00 00 00 00 11 b2 d0 50 00 00 00 00 01 00 00 00  .......P........
0030   00 00 00 00 00 00 00 00 00 00 00 00 00 00 ff ff  ................
0040   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
0050   00 00 00 00 00 00 00 00 ff ff 00 00 00 00 00 00  ................
0060   3b 2e b3 5d 8c e6 17 65 0f 2f 53 61 74 6f 73 68  ;..]...e./Satosh
0070   69 3a 30 2e 37 2e 32 2f c0 3e 03 00              i:0.7.2/.>..

Message Header:
 F9 BE B4 D9                                                                   - Main network magic bytes
 76 65 72 73 69 6F 6E 00 00 00 00 00                                           - "version" command
 64 00 00 00                                                                   - Payload is 100 bytes long
 35 8d 49 32                                                                   - payload checksum (little endian)

Version message:
 62 EA 00 00                                                                   - 60002 (protocol version 60002)
 01 00 00 00 00 00 00 00                                                       - 1 (NODE_NETWORK services)
 11 B2 D0 50 00 00 00 00                                                       - Tue Dec 18 10:12:33 PST 2012
 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 FF FF 00 00 00 00 00 00 - Recipient address info - see Network Address
 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 FF FF 00 00 00 00 00 00 - Sender address info - see Network Address
 3B 2E B3 5D 8C E6 17 65                                                       - Node ID
 0F 2F 53 61 74 6F 73 68 69 3A 30 2E 37 2E 32 2F                               - "/Satoshi:0.7.2/" sub-version string (string is 15 bytes long)
 C0 3E 03 00                                                                   - Last block sending node has is block #212672

verack

The verack message is sent in reply to version. This message consists of only a message header with the command string "verack".

Hexdump of the verack message: 

0000   F9 BE B4 D9 76 65 72 61  63 6B 00 00 00 00 00 00   ....verack......
0010   00 00 00 00 5D F6 E0 E2                            ........

Message header:
 F9 BE B4 D9                          - Main network magic bytes
 76 65 72 61  63 6B 00 00 00 00 00 00 - "verack" command
 00 00 00 00                          - Payload is 0 bytes long
 5D F6 E0 E2                          - Checksum (little endian)

addr

Provide information on known nodes of the network. Non-advertised nodes should be forgotten after typically 3 hours

Payload:

Field Size Description Data type Comments
1+ count var_int Number of address entries (max: 1000)
30x? addr_list (uint32_t + net_addr)[] Address of other nodes on the network. version < 209 will only read the first one. The uint32_t is a timestamp (see note below).

Note: Starting version 31402, addresses are prefixed with a timestamp. If no timestamp is present, the addresses should not be relayed to other peers, unless it is indeed confirmed they are up.

Hexdump example of addr message: 

0000   F9 BE B4 D9 61 64 64 72  00 00 00 00 00 00 00 00   ....addr........
0010   1F 00 00 00 ED 52 39 9B  01 E2 15 10 4D 01 00 00   .....R9.....M...
0020   00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 FF   ................
0030   FF 0A 00 00 01 20 8D                               ..... .

Message Header:
 F9 BE B4 D9                                     - Main network magic bytes
 61 64 64 72  00 00 00 00 00 00 00 00            - "addr"
 1F 00 00 00                                     - payload is 31 bytes long
 ED 52 39 9B                                     - payload checksum (little endian)

Payload:
 01                                              - 1 address in this message

Address:
 E2 15 10 4D                                     - Mon Dec 20 21:50:10 EST 2010 (only when version is >= 31402)
 01 00 00 00 00 00 00 00                         - 1 (NODE_NETWORK service - see version message)
 00 00 00 00 00 00 00 00 00 00 FF FF 0A 00 00 01 - IPv4: 10.0.0.1, IPv6: ::ffff:10.0.0.1 (IPv4-mapped IPv6 address)
 20 8D                                           - port 8333

inv

Allows a node to advertise its knowledge of one or more objects. It can be received unsolicited, or in reply to getblocks.

Payload (maximum 50,000 entries, which is just over 1.8 megabytes):

Field Size Description Data type Comments
1+ count var_int Number of inventory entries
36x? inventory inv_vect[] Inventory vectors

getdata

getdata is used in response to inv, to retrieve the content of a specific object, and is usually sent after receiving an inv packet, after filtering known elements. It can be used to retrieve transactions, but only if they are in the memory pool or relay set - arbitrary access to transactions in the chain is not allowed to avoid having clients start to depend on nodes having full transaction indexes (which modern nodes do not).

Payload (maximum 50,000 entries, which is just over 1.8 megabytes):

Field Size Description Data type Comments
1+ count var_int Number of inventory entries
36x? inventory inv_vect[] Inventory vectors

notfound

notfound is a response to a getdata, sent if any requested data items could not be relayed, for example, because the requested transaction was not in the memory pool or relay set.

Field Size Description Data type Comments
1+ count var_int Number of inventory entries
36x? inventory inv_vect[] Inventory vectors

getblocks

Return an inv packet containing the list of blocks starting right after the last known hash in the block locator object, up to hash_stop or 500 blocks, whichever comes first.

The locator hashes are processed by a node in the order as they appear in the message. If a block hash is found in the node's main chain, the list of its children is returned back via the inv message and the remaining locators are ignored, no matter if the requested limit was reached, or not.

To receive the next blocks hashes, one needs to issue getblocks again with a new block locator object. Keep in mind that some clients may provide blocks which are invalid if the block locator object contains a hash on the invalid branch.

Payload:

Field Size Description Data type Comments
4 version uint32_t the protocol version
1+ hash count var_int number of block locator hash entries
32+ block locator hashes char[32] block locator object; newest back to genesis block (dense to start, but then sparse)
32 hash_stop char[32] hash of the last desired block; set to zero to get as many blocks as possible (500)

To create the block locator hashes, keep pushing hashes until you go back to the genesis block. After pushing 10 hashes back, the step backwards doubles every loop: 

// From libbitcoin which is under AGPL
std::vector<size_t> block_locator_indexes(size_t top_height)
{
    std::vector<size_t> indexes;

    // Modify the step in the iteration.
    int64_t step = 1;

    // Start at the top of the chain and work backwards.
    for (auto index = (int64_t)top_height; index > 0; index -= step)
    {
        // Push top 10 indexes first, then back off exponentially.
        if (indexes.size() >= 10)
            step *= 2;

        indexes.push_back((size_t)index);
    }

    //  Push the genesis block index.
    indexes.push_back(0);
    return indexes;
}

Note that it is allowed to send in fewer known hashes down to a minimum of just one hash. However, the purpose of the block locator object is to detect a wrong branch in the caller's main chain. If the peer detects that you are off the main chain, it will send in block hashes which are earlier than your last known block. So if you just send in your last known hash and it is off the main chain, the peer starts over at block #1.

getheaders

Return a headers packet containing the headers of blocks starting right after the last known hash in the block locator object, up to hash_stop or 2000 blocks, whichever comes first. To receive the next block headers, one needs to issue getheaders again with a new block locator object. Keep in mind that some clients may provide headers of blocks which are invalid if the block locator object contains a hash on the invalid branch.

Payload:

Field Size Description Data type Comments
4 version uint32_t the protocol version
1+ hash count var_int number of block locator hash entries
32+ block locator hashes char[32] block locator object; newest back to genesis block (dense to start, but then sparse)
32 hash_stop char[32] hash of the last desired block header; set to zero to get as many blocks as possible (2000)

For the block locator object in this packet, the same rules apply as for the getblocks packet.

tx

tx describes a bitcoin transaction, in reply to getdata. When a bloom filter is applied tx objects are sent automatically for matching transactions following the merkleblock.


Field Size Description Data type Comments
4 version int32_t Transaction data format version (note, this is signed)
1+ tx_in count var_int Number of Transaction inputs (never zero)
41+ tx_in tx_in[] A list of 1 or more transaction inputs or sources for coins
1+ tx_out count var_int Number of Transaction outputs
9+ tx_out tx_out[] A list of 1 or more transaction outputs or destinations for coins
4 lock_time uint32_t The block number or timestamp at which this transaction is unlocked:
Value Description
0 Not locked
< 500000000 Block number at which this transaction is unlocked
>= 500000000 UNIX timestamp at which this transaction is unlocked

If all TxIn inputs have final (0xffffffff) sequence numbers then lock_time is irrelevant. Otherwise, the transaction may not be added to a block until after lock_time (see NLockTime).

TxIn consists of the following fields:

Field Size Description Data type Comments
36 previous_output outpoint The previous output transaction reference, as an OutPoint structure
1+ script length var_int The length of the signature script
? signature script uchar[] Computational Script for confirming transaction authorization
4 sequence uint32_t Transaction version as defined by the sender. Intended for "replacement" of transactions when information is updated before inclusion into a block.

The OutPoint structure consists of the following fields:

Field Size Description Data type Comments
32 hash char[32] The hash of the referenced transaction.
4 index uint32_t The index of the specific output in the transaction. The first output is 0, etc.

The Script structure consists of a series of pieces of information and operations related to the value of the transaction.

(Structure to be expanded in the future… see script.h and script.cpp and Script for more information)

The TxOut structure consists of the following fields:

Field Size Description Data type Comments
8 value int64_t Transaction Value
1+ pk_script length var_int Length of the pk_script
? pk_script uchar[] Contains the ScriptPubKey setting up conditions to claim this output.


Example tx message: 

000000	F9 BE B4 D9 74 78 00 00  00 00 00 00 00 00 00 00   ....tx..........
000010	02 01 00 00 E2 93 CD BE  01 00 00 00 01 6D BD DB   .............m..
000020	08 5B 1D 8A F7 51 84 F0  BC 01 FA D5 8D 12 66 E9   .[...Q........f.
000030	B6 3B 50 88 19 90 E4 B4  0D 6A EE 36 29 00 00 00   .;P......j.6)...
000040	00 8B 48 30 45 02 21 00  F3 58 1E 19 72 AE 8A C7   ..H0E.!..X..r...
000050	C7 36 7A 7A 25 3B C1 13  52 23 AD B9 A4 68 BB 3A   .6zz%;..R#...h.:
000060	59 23 3F 45 BC 57 83 80  02 20 59 AF 01 CA 17 D0   Y#?E.W... Y.....
000070	0E 41 83 7A 1D 58 E9 7A  A3 1B AE 58 4E DE C2 8D   .A.z.X.z...XN...
000080	35 BD 96 92 36 90 91 3B  AE 9A 01 41 04 9C 02 BF   5...6..;...A....
000090	C9 7E F2 36 CE 6D 8F E5  D9 40 13 C7 21 E9 15 98   .~.6.m...@..!...
0000A0	2A CD 2B 12 B6 5D 9B 7D  59 E2 0A 84 20 05 F8 FC   *.+..].}Y... ...
0000B0	4E 02 53 2E 87 3D 37 B9  6F 09 D6 D4 51 1A DA 8F   N.S..=7.o...Q...
0000C0	14 04 2F 46 61 4A 4C 70  C0 F1 4B EF F5 FF FF FF   ../FaJLp..K.....
0000D0	FF 02 40 4B 4C 00 00 00  00 00 19 76 A9 14 1A A0   [email protected]....
0000E0	CD 1C BE A6 E7 45 8A 7A  BA D5 12 A9 D9 EA 1A FB   .....E.z........
0000F0	22 5E 88 AC 80 FA E9 C7  00 00 00 00 19 76 A9 14   "^...........v..
000100	0E AB 5B EA 43 6A 04 84  CF AB 12 48 5E FD A0 B7   ..[.Cj.....H^...
000110	8B 4E CC 52 88 AC 00 00  00 00                     .N.R......


Message header:
 F9 BE B4 D9                                       - main network magic bytes
 74 78 00 00 00 00 00 00 00 00 00 00               - "tx" command
 02 01 00 00                                       - payload is 258 bytes long
 E2 93 CD BE                                       - payload checksum (little endian)

Transaction:
 01 00 00 00                                       - version

Inputs:
 01                                                - number of transaction inputs

Input 1:
 6D BD DB 08 5B 1D 8A F7  51 84 F0 BC 01 FA D5 8D  - previous output (outpoint)
 12 66 E9 B6 3B 50 88 19  90 E4 B4 0D 6A EE 36 29
 00 00 00 00

 8B                                                - script is 139 bytes long

 48 30 45 02 21 00 F3 58  1E 19 72 AE 8A C7 C7 36  - signature script (scriptSig)
 7A 7A 25 3B C1 13 52 23  AD B9 A4 68 BB 3A 59 23
 3F 45 BC 57 83 80 02 20  59 AF 01 CA 17 D0 0E 41
 83 7A 1D 58 E9 7A A3 1B  AE 58 4E DE C2 8D 35 BD
 96 92 36 90 91 3B AE 9A  01 41 04 9C 02 BF C9 7E
 F2 36 CE 6D 8F E5 D9 40  13 C7 21 E9 15 98 2A CD
 2B 12 B6 5D 9B 7D 59 E2  0A 84 20 05 F8 FC 4E 02
 53 2E 87 3D 37 B9 6F 09  D6 D4 51 1A DA 8F 14 04
 2F 46 61 4A 4C 70 C0 F1  4B EF F5

 FF FF FF FF                                       - sequence

Outputs:
 02                                                - 2 Output Transactions

Output 1:
 40 4B 4C 00 00 00 00 00                           - 0.05 BTC (5000000)
 19                                                - pk_script is 25 bytes long

 76 A9 14 1A A0 CD 1C BE  A6 E7 45 8A 7A BA D5 12  - pk_script
 A9 D9 EA 1A FB 22 5E 88  AC

Output 2:
 80 FA E9 C7 00 00 00 00                           - 33.54 BTC (3354000000)
 19                                                - pk_script is 25 bytes long

 76 A9 14 0E AB 5B EA 43  6A 04 84 CF AB 12 48 5E  - pk_script
 FD A0 B7 8B 4E CC 52 88  AC

Locktime:
 00 00 00 00                                       - lock time

block

The block message is sent in response to a getdata message which requests transaction information from a block hash.

Field Size Description Data type Comments
4 version int32_t Block version information (note, this is signed)
32 prev_block char[32] The hash value of the previous block this particular block references
32 merkle_root char[32] The reference to a Merkle tree collection which is a hash of all transactions related to this block
4 timestamp uint32_t A Unix timestamp recording when this block was created (Currently limited to dates before the year 2106!)
4 bits uint32_t The calculated difficulty target being used for this block
4 nonce uint32_t The nonce used to generate this block… to allow variations of the header and compute different hashes
1+ txn_count var_int Number of transaction entries
? txns tx[] Block transactions, in format of "tx" command

The SHA256 hash that identifies each block (and which must have a run of 0 bits) is calculated from the first 6 fields of this structure (version, prev_block, merkle_root, timestamp, bits, nonce, and standard SHA256 padding, making two 64-byte chunks in all) and not from the complete block. To calculate the hash, only two chunks need to be processed by the SHA256 algorithm. Since the nonce field is in the second chunk, the first chunk stays constant during mining and therefore only the second chunk needs to be processed. However, a Bitcoin hash is the hash of the hash, so two SHA256 rounds are needed for each mining iteration. See Block hashing algorithm for details and an example.

headers

The headers packet returns block headers in response to a getheaders packet.

Payload:

Field Size Description Data type Comments
1+ count var_int Number of block headers
81x? headers block_header[] Block headers

Note that the block headers in this packet include a transaction count (a var_int, so there can be more than 81 bytes per header) as opposed to the block headers that are hashed by miners.

getaddr

The getaddr message sends a request to a node asking for information about known active peers to help with finding potential nodes in the network. The response to receiving this message is to transmit one or more addr messages with one or more peers from a database of known active peers. The typical presumption is that a node is likely to be active if it has been sending a message within the last three hours.

No additional data is transmitted with this message.

mempool

The mempool message sends a request to a node asking for information about transactions it has verified but which have not yet confirmed. The response to receiving this message is an inv message containing the transaction hashes for all the transactions in the node's mempool.

No additional data is transmitted with this message.

It is specified in BIP 35. Since BIP 37, if a bloom filter is loaded, only transactions matching the filter are replied.

checkorder

This message was used for IP Transactions. As IP transactions have been deprecated, it is no longer used.

submitorder

This message was used for IP Transactions. As IP transactions have been deprecated, it is no longer used.

reply

This message was used for IP Transactions. As IP transactions have been deprecated, it is no longer used.

ping

The ping message is sent primarily to confirm that the TCP/IP connection is still valid. An error in transmission is presumed to be a closed connection and the address is removed as a current peer.

Payload:

Field Size Description Data type Comments
8 nonce uint64_t random nonce

pong

The pong message is sent in response to a ping message. In modern protocol versions, a pong response is generated using a nonce included in the ping.

Payload:

Field Size Description Data type Comments
8 nonce uint64_t nonce from ping


reject

The reject message is sent when messages are rejected.

Payload:

Field Size Description Data type Comments
1+ message var_str type of message rejected
1 ccode char code relating to rejected message
1+ reason var_str text version of reason for rejection
0+ data char Optional extra data provided by some errors. Currently, all errors which provide this field fill it with the TXID or block header hash of the object being rejected, so the field is 32 bytes.

CCodes

Value Name Description
0x01 REJECT_MALFORMED
0x10 REJECT_INVALID
0x11 REJECT_OBSOLETE
0x12 REJECT_DUPLICATE
0x40 REJECT_NONSTANDARD
0x41 REJECT_DUST
0x42 REJECT_INSUFFICIENTFEE
0x43 REJECT_CHECKPOINT

filterload, filteradd, filterclear, merkleblock

These messages are related to Bloom filtering of connections and are defined in BIP 0037.


The filterload command is defined as follows:

Field Size Description Data type Comments
? filter uint8_t[] The filter itself is simply a bit field of arbitrary byte-aligned size. The maximum size is 36,000 bytes.
4 nHashFuncs uint32_t The number of hash functions to use in this filter. The maximum value allowed in this field is 50.
4 nTweak uint32_t A random value to add to the seed value in the hash function used by the bloom filter.
1 nFlags uint8_t A set of flags that control how matched items are added to the filter.

See below for a description of the Bloom filter algorithm and how to select nHashFuncs and filter size for a desired false positive rate.

Upon receiving a filterload command, the remote peer will immediately restrict the broadcast transactions it announces (in inv packets) to transactions matching the filter, where the matching algorithm is specified below. The flags control the update behaviour of the matching algorithm.

The filteradd command is defined as follows:

Field Size Description Data type Comments
? data uint8_t[] The data element to add to the current filter.

The data field must be smaller than or equal to 520 bytes in size (the maximum size of any potentially matched object).

The given data element will be added to the Bloom filter. A filter must have been previously provided using filterload. This command is useful if a new key or script is added to a clients wallet whilst it has connections to the network open, it avoids the need to re-calculate and send an entirely new filter to every peer (though doing so is usually advisable to maintain anonymity).

The filterclear command has no arguments at all.

After a filter has been set, nodes don't merely stop announcing non-matching transactions, they can also serve filtered blocks. A filtered block is defined by the merkleblock message and is defined like this:

Field Size Description Data type Comments
4 version int32_t Block version information, based upon the software version creating this block (note, this is signed)
32 prev_block char[32] The hash value of the previous block this particular block references
32 merkle_root char[32] The reference to a Merkle tree collection which is a hash of all transactions related to this block
4 timestamp uint32_t A timestamp recording when this block was created (Limited to 2106!)
4 bits uint32_t The calculated difficulty target being used for this block
4 nonce uint32_t The nonce used to generate this block… to allow variations of the header and compute different hashes
4 total_transactions uint32_t Number of transactions in the block (including unmatched ones)
1+ hash_count var_int The number of hashes to follow
32x? hashes char[32] Hashes in depth-first order
1+ flag_bytes var_int The size of flags (in bytes) to follow
? flags byte[] Flag bits, packed per 8 in a byte, least significant bit first. Extra 0 bits are padded on to reach full byte size.

After a merkleblock, transactions matching the bloom filter are automatically sent in tx messages.

A guide to creating a bloom filter, loading a merkle block, and parsing a partial merkle block tree can be found in the Developer Examples.

sendheaders

Request for Direct headers announcement.

Upon receipt of this message, the node is be permitted, but not required, to announce new blocks by headers command (instead of inv command).

This message is supported by the protocol version >= 70012 or Bitcoin Core version >= 0.12.0.

See BIP 130 for more information.

No additional data is transmitted with this message.


feefilter

The payload is always 8 bytes long and it encodes 64 bit integer value (LSB / little endian) of feerate. The value represents a minimal fee and is expressed in satoshis per 1000 bytes.

Upon receipt of a "feefilter" message, the node will be permitted, but not required, to filter transaction invs for transactions that fall below the feerate provided in the feefilter message interpreted as satoshis per kilobyte.

The fee filter is additive with a bloom filter for transactions so if an SPV client were to load a bloom filter and send a feefilter message, transactions would only be relayed if they passed both filters.

Inv's generated from a mempool message are also subject to a fee filter if it exists.

Feature discovery is enabled by checking protocol version >= 70013

See BIP 133 for more information.

sendcmpct

  1. The sendcmpct message is defined as a message containing a 1-byte integer followed by a 8-byte integer where pchCommand == "sendcmpct".
  2. The first integer SHALL be interpreted as a boolean (and MUST have a value of either 1 or 0)
  3. The second integer SHALL be interpreted as a little-endian version number. Nodes sending a sendcmpct message MUST currently set this value to 1.
  4. Upon receipt of a "sendcmpct" message with the first and second integers set to 1, the node SHOULD announce new blocks by sending a cmpctblock message.
  5. Upon receipt of a "sendcmpct" message with the first integer set to 0, the node SHOULD NOT announce new blocks by sending a cmpctblock message, but SHOULD announce new blocks by sending invs or headers, as defined by BIP130.
  6. Upon receipt of a "sendcmpct" message with the second integer set to something other than 1, nodes MUST treat the peer as if they had not received the message (as it indicates the peer will provide an unexpected encoding in
  7. cmpctblock, and/or other, messages). This allows future versions to send duplicate sendcmpct messages with different versions as a part of a version handshake for future versions.
  8. Nodes SHOULD check for a protocol version of >= 70014 before sending sendcmpct messages.
  9. Nodes MUST NOT send a request for a MSG_CMPCT_BLOCK object to a peer before having received a sendcmpct message from that peer.

This message is only supported by protocol version >= 70014

See BIP 152 for more information.

cmpctblock

  1. The cmpctblock message is defined as as a message containing a serialized HeaderAndShortIDs message and pchCommand == "cmpctblock".
  2. Upon receipt of a cmpctblock message after sending a sendcmpct message, nodes SHOULD calculate the short transaction ID for each unconfirmed transaction they have available (ie in their mempool) and compare each to each short transaction ID in the cmpctblock message.
  3. After finding already-available transactions, nodes which do not have all transactions available to reconstruct the full block SHOULD request the missing transactions using a getblocktxn message.
  4. A node MUST NOT send a cmpctblock message unless they are able to respond to a getblocktxn message which requests every transaction in the block.
  5. A node MUST NOT send a cmpctblock message without having validated that the header properly commits to each transaction in the block, and properly builds on top of the existing chain with a valid proof-of-work. A node MAY send a cmpctblock before validating that each transaction in the block validly spends existing UTXO set entries.

This message is only supported by protocol version >= 70014

See BIP 152 for more information.

getblocktxn

  1. The getblocktxn message is defined as as a message containing a serialized BlockTransactionsRequest message and pchCommand == "getblocktxn".
  2. Upon receipt of a properly-formatted getblocktxnmessage, nodes which recently provided the sender of such a message a cmpctblock for the block hash identified in this message MUST respond with an appropriate blocktxn message. Such a blocktxn message MUST contain exactly and only each transaction which is present in the appropriate block at the index specified in the getblocktxn indexes list, in the order requested.

This message is only supported by protocol version >= 70014

See BIP 152 for more information.

blocktxn

  1. The blocktxn message is defined as as a message containing a serialized BlockTransactions message and pchCommand == "blocktxn".
  2. Upon receipt of a properly-formatted requested blocktxn message, nodes SHOULD attempt to reconstruct the full block by:
  3. Taking the prefilledtxn transactions from the original cmpctblock and placing them in the marked positions.
  4. For each short transaction ID from the original cmpctblock, in order, find the corresponding transaction either from the blocktxn message or from other sources and place it in the first available position in the block.
  5. Once the block has been reconstructed, it shall be processed as normal, keeping in mind that short transaction IDs are expected to occasionally collide, and that nodes MUST NOT be penalized for such collisions, wherever they appear.

This message is only supported by protocol version >= 70014

See BIP 152 for more information.

Scripting

See Advanced Bitcoin Scripting.

See Also

Attribution

This content is based on content sourced from https://en.bitcoin.it/wiki/Protocol_documentation under Creative Commons Attribution 3.0. Although it may have been extensively revised and updated we acknowledge the original authors.

Retrieved from "https://wiki.bitcoinsv.io/index.php?title=Peer-To-Peer_Protocol&oldid=2119"